Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
What position do you place the forks when parking your forklift?
Travel with forks as low as possible from the floor and tilted back (usually within 10-15 cm (4 to 6 inches) above the floor). Match speed to, load, presence of pedestrians, obstructions, and driving and workplace conditions, including slippery surfaces.
When traveling with empty forklift the forks should be in what position?
When travelling in an empty forklift, the forks of the lift should be in the position of waist high.
How do you adjust forklift forks?
How Do I Make an Adjustment of Width of a Forklift Fork?
- Determine the best setting for the forks on your forklift. …
- Raise the forks to a height of approximately 30 inches. …
- Raise the fork slightly. …
- Shift the fork slightly until it drops into the notch nearest the desired distance.
How should you normally drive your forklift?
To reduce these hazards, follow these requirements and recommendations:
- Always drive unloaded forklifts with the forks downgrade.
- Never drive a loaded forklift with the load downgrade.
- When driving up a ramp, drive loaded forklifts forward with the load upgrade.
Is it illegal to leave keys in a forklift?
You might not be aware but it is actually illegal to leave the keys in an unattended Forklift. This measure is to prevent unauthorised use of the Forklift. … All forklifts and plant equipment can be fitted with low cost Driver Identification systems which prevent unauthorised usage.
Which side of the forklift is supporting more weight?
Weight distribution refers not only to the weight of the load, but also the weight of the forklift itself. An empty forklift has most of its weight in the rear, but when a load is placed on the lift, the weight distribution moves forward.
What is the recommended speed limit for a forklift?
The Material Handling Equipment Distributors Association (MHEDA) recommends a max speed of 8 mph in general and a 3 mph max speed in areas where pedestrians are present.
When moving a forklift with no load the forks should stay?
Figure 7. Traveling down ramp without load. Requirements and Recommended Practices: When traveling without a load, the forks should point downgrade, regardless of direction of travel.
When picking up a load the correct fork spacing should be?
-The forklift operator should stop 8 to 12 inches (20 to 30 cms) from the load. – It should be ensured that the forklift is placed squarely facing the load and the forks are positioned at the correct height.
What is side shift on a forklift?
When installed on a forklift a side-shift allows a carried load to be moved left or right within a given span. The major advantage of side-shift is the ability to move the fork carriage without having to move the whole forklift. Some other benefits of side-shift include: Ability to shift loads in tight spaces.
Can you flip the forks on a forklift?
Just like Bubba in Forest Gump knows everything there is to know about the shrimping business, there is a lot to know about forklift forks. You can lift with them, sideshift them, fork position them, and even rotate them.
What is the counterweight on a forklift made of?
Forklift counterweights are made of either full cast iron, full concrete or a combined mix of metal and concrete. CARRIAGE.
Why do forklifts have 3 pedals?
To begin with, every forklift comes equipped with an accelerator and a brake pedal. That third pedal is called an Inching Brake. … It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.
What are 3 fluid levels that need to be checked before using the forklift?
Check of liquid Levels:
- Hydraulic fluid.
- Brake fluid.
- Engine oil coolant.
Is forklift driving hard?
Driving a forklift isn’t all cake, roses, and gas pedals. It’s going to be hard work. … Operating a forklift is considered a “hazardous occupation,” according to the Fair Labor Standards Act. As with any big machine, accidents happen.