Frequent question: How long does it take to charge a Skyjack scissor lift?

All scissor lifts are slightly different, but the main rule of thumb is allowing your scissor lift to charge for at least 6 hours before you can get the full life out of it the next day. Scissor lifts are designed to be able to be used throughout the day and charged each night or every other night depending on usage.

How long does it take a lift to charge?

A flat battery can take approximately 2 hours to fully charge (using the smart charger). The red charge light will turn to green on the battery charger to indicate when charging is complete. It can remain in this state on trickle charge until your next bath, if required, without the risk of overcharging.

Can you use a Skyjack scissor lift while charging?

It is important to note that it is possible to use your scissor lift whilst the battery is being charged. All you need to do is pull the red emergency shut-off button out and have a helper guide the extension cord away from the wheels whilst the equipment is moving.

THIS IS INTERESTING:  What is a hoist used for?

How do you know if Skyjack is charging?

The charger will automatically begin charging the batteries within the scissor lift. The lights will turn green when the batteries are fully charged. The charger will automatically shut off. On older models with a meter, the charger will automatically shut off and the meter will read zero volts when fully charged.

How long does a scissor lift battery last?

A poorly maintained battery may need to be replaced within one year, whereas a well-maintained battery can last as long as three years. However, new innovations such as battery monitoring on electric scissor lifts can significantly extend battery life beyond a few years, while greatly lowering service costs.

Can you drive a scissor lift while charging?

It is important to note that it is possible to use your scissor lift whilst the battery is being charged. All you need to do is pull the red emergency shut-off button out and have a helper guide the extension cord away from the wheels whilst the equipment is moving.

Can you charge a scissor lift with a generator?

For units that will be used where there is no plug-in power, or that will work multiple shifts daily, the optional onboard gasoline-fueled charging generator can recharge the batteries while the lift is in use.

Where are Skyjack scissor lifts made?

After launching Quest2013, the company received entries from places as far away as Latvia, India, Argentina, Germany and other countries from around the world. To its surprise, the oldest working unit was found less than four kilometers from Skyjack’s factory in Guelph, Ontario, Canada.

THIS IS INTERESTING:  What rules must be followed while hoisting the national flag?

What is a scissors lift?

A scissor lift is a machine made to move personnel and equipment in a vertical direction. These lifts can handle any application that would normally require a ladder, tower or scaffolding.

How much does a Genie scissor lift weight?

The Genie® GS™-1932 slab scissor lifts boast quiet electric operation and are ideal for indoor and outdoor applications in tight spaces on firm, level surfaces.

GS-1932 & GS-1932 E-Drive.

Specificatijon Value
Capacity 500 lb
Machine Width 2 ft 8 in
Machine Length 6 ft
Weight 2,929 lb

How do you charge a Genie GS 1930 scissor lift?

Do not use any battery charger greater than 24V to charge the batteries. Connect the battery charger to a grounded, AC 3-wire electrical outlet only. Inspect daily for damaged cord, cables and wires.

How do you maintain a scissor lift?

Like all heavy equipment, scissor and boom lifts require periodic maintenance and inspections to ensure equipment is running efficiently, helping operators maintain productivity. Scissor lifts and boom lifts should be inspected before use every day, at shift changes, and any time a new operator takes over the machine.

Can a scissor lift get wet?

Wet conditions mean slippery conditions for both the wheels on your scissor lift hire and for the staff working on them. As most access equipment is made primarily from metals such as steel, when these surface materials get wet, there is very little traction for those on board.

How many batteries does a scissor lift take?

Smaller booms and scissor lifts will typically have four, 6V batteries, while larger machines will include a bank of eight, 6V batteries. Verify that all the batteries are charging properly and replace bad batteries.

THIS IS INTERESTING:  What class of forklift is a combilift?
Special equipment and operation