How do you put a forklift in reverse?

Shift the forklift into reverse, disengage the parking brake, and use the accelerator to slowly back out from the load. Make sure not to turn or else you could knock the load over. Don’t forget to lower the fork closer to the ground before you start driving again.

What should the operator do before reversing a forklift?

When reversing the forklift, always do so slowly. It’s easy to lose control at speed, especially if the load you’re carrying is very heavy or bulky. Be sure to sound your horn before you reverse to alert pedestrians and other vehicular traffic of your presence.

Are you supposed to drive a forklift backwards?

The driver will slow down and sound the horn at cross aisles and other locations where vision is obstructed. If the load being carried obstructs forward view, the driver will be required to travel in reverse, with the load trailing.

THIS IS INTERESTING:  How many hours does a forklift operator work?

How do you put a Hyster forklift in reverse?

Pull the middle lever toward you to tilt the mast toward the forklift. Release the parking brake and move the directional lever toward the direction you need to travel. Release the brake to start moving. If moving in reverse, make sure the back-up siren is working properly.

What are the 3 pedals on a forklift for?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

Is driving a forklift easy?

For a novice, driving forklift can be a daunting task. … Just like an ordinary sedan car, a forklift can be fairly easy to operate. It only takes short time and little practice for you to get a grasp of it. But make no mistake, just because it is easy to operate, does it mean you will put your guard down.

A forklift platform must comply with HSE PM28 regulations in addition to being fully compatible with the forklift truck. … A forklift truck cage must be secured to the truck itself or the forks.

What steps should you do every time you park a forklift?

Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.

THIS IS INTERESTING:  Does lifting your truck void your warranty?

What are 3 fluid levels that need to be checked before using the forklift?

Check of liquid Levels:

  • Hydraulic fluid.
  • Brake fluid.
  • Engine oil coolant.
  • Battery.
  • Fuel.

20.04.2011

When should you drive backwards on a forklift?

If a load on the forks blocks your view of the intended path of travel, travel in reverse. Always maintain a safe distance from the forklift ahead of you (about three truck lengths)

Why do Forklifts drive backwards?

Forklift operators spend a great deal of time driving in reverse. Large loads on the forks can sometimes obscure operator vision, making it necessary to drive backwards for maximum visibility.

When driving a forklift how high should the forks be off the ground?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy.

What is the inching pedal on a forklift?

The purpose of the inching pedal is to disengage the transmission without having to shift the gear lever into neutral every time a lift is performed. This pedal allows you to bring the forklift to a stop or to slow it down.

What does the second hydraulic control lever on a forklift control?

Hydraulic Lift Knobs – Forklift has three basic controls knobs. One that lifts the forks up or down, the second one tilts the forks/blades down or up to secure the load, and the third to move the load side to side. Some types of forklifts have a knob that controls the width of the fork.

Special equipment and operation