How should pedestrian access be restricted when operating a forklift?

1. Create clear walkways. The best way to protect pedestrians from forklift injuries is to prohibit pedestrian traffic in forklift areas. Pedestrian walkways above forklift areas can keep foot traffic separate from forklift traffic, but some buildings may not be designed in a way that can accommodate elevated walkways.

Do forklifts give way to pedestrians?

Pedestrians Prohibited – Forklift Operating Area. Forklift and Powered Loadshifting Equipment Prohibited. … Pedestrians must give way to vehicles.

What is the pedestrian exclusion zone around a forklift?

Designate exclusion zones for pedestrians and forklifts. Pedestrian exclusion zones should be enforced within a three metre radius of a forklift. This distance should expand when the height of the forklift load or the speed travelled increases.

What should not be done when operating a forklift?

Do not grab the overhead guard when traveling in reverse. Doing so could expose the operator’s finger to serious injury. Never turn on a grade or with the forks elevated. Do not carry passengers.

THIS IS INTERESTING:  Can you buy a forklift?

Which safety precaution applies to forklifts?

Forklift operators should be dressed with the appropriate safety equipment, including safety shoes, hard-hats, and a high-visibility jacket. Make sure to tuck away loose clothing to prevent it from getting caught on the forklift.

When picking up a load the forks should be?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.

How do you separate pedestrians and forklifts?

Physically separating these paths using railings or barriers adds an extra level of separation. While this separation is ideal, it cannot always be attained. When forklift and pedestrian paths are shared, make sure there is adequate walking space on the side of forklift lanes and walkway striping on the floor.

How far should you stand from a forklift?

The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.

How far away from a moving forklift should you stay?

Falling distance of an object from a pallet or 15 feet, 5 Feet both sides, 5 Feet Rear of Forklift. do so (ALL CLEAR). Do not pass under the forks while in operation. in operation and a fix object.

What distance must you keep from an operating forklift?

For example, even at six kilometres an hour (i.e. walking pace) a forklift needs at least three metres to stop. The distance at which a forklift can stop is affected by: • the speed at which it is travelling • the weight of its load • its mechanical and tyre condition • the road surface.

THIS IS INTERESTING:  You asked: Where does the prime minister hoist the flag?

What are 3 fluid levels that need to be checked before using the forklift?

Check of liquid Levels:

  • Hydraulic fluid.
  • Brake fluid.
  • Engine oil coolant.
  • Battery.
  • Fuel.

20.04.2011

Do and don’ts of forklift?

The 5 Dos and Don’ts of Forklift Safety

  • Do Drive Responsibly. Just like driving a car on the road, you should always operate your forklift at a speed that will allow you to stop safely. …
  • Don’t Go Over Your Forklift’s Load Capacity. …
  • Do Be Aware of Pedestrians. …
  • Don’t Skimp on Training. …
  • Do Maintain Your Forklift.

7.12.2015

What steps should you do every time you park a forklift?

Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.

What is your duty of care while operating a forklift?

a) Provide and maintain a work environment without risks to health and safety; b) Provide and maintain safe plant and structures; c) Provide and maintain safe systems of work; d) Provide adequate facilities; … f) Make arrangements to ensure the safe use, handling and storage of plant, structures and substances.

What are the controls on a forklift?

Hydraulic Lift Knobs: Forklift has three basic controls knobs. One that lifts the forks up or down, the second one tilts the forks/blades down or up to secure the load, and the third to move the load side to side. Some types of forklifts have a knob that controls the width of the fork.

THIS IS INTERESTING:  How does a crane use pulleys?

What is the most common type of forklift?

Counterbalance Lift

The Counterbalance is the most common type of forklift. This type of lift has its forks at the front of the machine and is designed with a weight in the back to offset or counter the balance of the load on the front.

Special equipment and operation