Quick Answer: Which steps should you follow to safely lift an object with the forks on a forklift truck?

Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator. Attend the controls of the forklift truck when a load is elevated.

Training Wheels354 подписчикаПодписатьсяForklift Training – How to lift a load – Part 5/6

How do you move the forks on a forklift?

Raise the fork slightly. The fork will be resting in a small groove in the crossbar; nudge the fork out of the notch so that it will slide along the top of the crossbar. If the forks are rarely adjusted they may be very hard to move. If so, move to the end of the fork and move it from side to side to break it free.

THIS IS INTERESTING:  Quick Answer: What is a Class 2 lift truck?

What should you do to lift a pallet and raise the forks on the truck?

Always travel load uphill, forks downhill — if travelling with a load, it should always face uphill; if unladen, forks should face downhill. This will improve stability, traction and adhesion, and applies regardless of the direction the operator is travelling in.

When picking up a load with a forklift the forks should be?

Carrying the load

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back.

Which steps should you do every time you park a forklift?

Parking Safety Rules

  • Always try to find a level surface to park on. …
  • Lower forks, or the forklift attachment, all the way to the ground. …
  • Put the gear into neutral.
  • Make sure the wheels are straight. …
  • Set the parking brake every time you park the forklift. …
  • Turn off the engine before dismounting the forklift.

What happens when a forklift is overloaded on the tip of the fork?

Deadly Danger # 1—Forklift Turnovers

Forklifts can easily tip if they are overloaded, if the load is not well balanced, or if they travel with the forks too high. How it can happen: A forklift operator was killed when his forklift overturned when he was turning while backing down an incline.

When traveling with empty forklift the forks should be in what position?

When travelling in an empty forklift, the forks of the lift should be in the position of waist high.

THIS IS INTERESTING:  How do you calculate the volume of a loader bucket?

Can you flip the forks on a forklift?

Just like Bubba in Forest Gump knows everything there is to know about the shrimping business, there is a lot to know about forklift forks. You can lift with them, sideshift them, fork position them, and even rotate them.

How low should forks be driving forklift?

Travel with forks as low as possible from the floor and tilted back (usually within 10-15 cm (4 to 6 inches) above the floor). Match speed to, load, presence of pedestrians, obstructions, and driving and workplace conditions, including slippery surfaces.

How should a lift operator travel with a full pallet on the forks?

If it’s a stable load and secure on the pallet, tilt first, then lift. Once the load is lifted, lower it to a safe traveling height. Keep the forks two to four inches off the floor if driving on a smooth surface.

How far should you stand from a forklift?

The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.

What should an operator do immediately after they find a problem with a lift truck?

Report any problems identified in daily check to the supervisor immediately. Check with your jurisdiction for any requirements regarding frequency of checks, and maintenance.

Which side of the forklift is supporting more weight?

Weight distribution refers not only to the weight of the load, but also the weight of the forklift itself. An empty forklift has most of its weight in the rear, but when a load is placed on the lift, the weight distribution moves forward.

THIS IS INTERESTING:  How many types of forklift licenses are there?

How should you carry an unbalanced load when one end is heavier?

If you must carry an unbalanced load, ensure that the heavy end is against the heel of the fork arms. Check the condition of load supports (e.g. pallet, container). The sudden collapse of block stacking has often been caused by these items being damaged or deteriorated.

Where is the vehicle specification plate on a forklift?

The forklift data plate can be found on the instrument panel near the operating controls. It is the responsibility of the operator to understand the capabilities of each forklift and to properly maintain the data plate to ensure it is legible and complete.

Special equipment and operation