A forklift’s rated load capacity is the maximum weight in kilograms that a forklift can safely lift and transport at a specified load centre distance in millimetres.
Where is the maximum rated capacity for the forklift located?
At 29 CFR 1910.178(o)(2), OSHA states that “only loads within the rated capacity of a truck shall be handled.” The rated capacity can be found on the “data plate” located on the forklift. You can see an example data plate below.
What is rated load capacity?
Rated Capacity is the maximum total load a crane can lift for a defined configuration. Rated Capacity is also known as the Maximum Rated Capacity (MRC) or Manufacturer’s Rated Capacity. … This is referred to as the Gross Load of the crane where the Net Load is the actual mass being lifted.
How is forklift capacity calculated?
The maximum Load Moment for a truck is derived by multiplying the weight rating of the forklift by the center load distance. If we multiply the 5,000-pound capacity of our theoretical forklift by its 24-inch center load, we arrive at a maximum Load Moment of 120,000 inch-pounds.
How are forklift forks rated?
The capacity can be found on the data tag, located on or near the dashboard of the forklift. Each set of forks has a rated capacity. This capacity includes a safety factor but should be used as the maximum lifting capacity for a set of 2 forks.
How much can a 10K forklift lift?
How much can a 10k forklift lift? Utilizing the Cat 928Hz platform, the 10K ATFL is capable of lifting and carrying 10,000 lbs, and is able to reach a height of 96” fully loaded. The open center hydraulic system provides precise load management, with maximum productivity.
How do I choose a forklift?
A Few Quick Tips for getting the Best Forklift
- Find a Trustworthy Brand.
- Think about What you Really Need (a good partner will help you figure that out)
- Know what kind of power you need (think about best fuel type and tire options)
How is rated capacity calculated?
The formula for capacity-utilization rate is actual output divided by the potential output. For example, say that a business has the capacity to produce 1,600 widgets a day as in the above example, but is only producing 1,400. The capacity utilization rate is 1,400 over 1,600, or 87.5 percent.
What is the rated capacity?
“Rated Capacity” is defined in the UN Model Regulations as follows: Rated capacity means the capacity, in ampere-hours, of a cell or battery as measured by subjecting it to a load, temperature and voltage cut-off point specified by the manufacturer.
Is SWL still used?
Today, SWL is not used anymore because it has been completely replaced by the term WLL. Let us discover the reasons why engineers put an end to using the term “safe working load.”
How do you calculate load capacity?
Take the total weight of the load and divide this by the number of legs supporting the load. For example, assume a 2,000 pound load is to be supported by 2 legs of a sling. The above will give a total minimum weight on each leg of the sling of 2,000 pounds divided by 2 legs or 1,000 pounds.
How do you calculate safe load capacity?
SWL or WLL are calculated by dividing MBL by a safety factor (SF). An example of this would be a chain that has a MBL of 2000 lbf (8.89 kN) would have a SWL or WLL of 400 lbf (1.78 kN) if a safety factor of 5 (5:1, 5 to 1, or 1/5) is used.
What is a Class 2 forklift?
Class II forklifts are electric, narrow aisle models. As the name suggests, Class II forklifts are designed with maneuverability that allows them to operate in tight spaces and narrow aisles.
How do you read a fork rating?
Forks come in two basic styles and a few specialty styles. Read below for a general description of each. ITA Style Forks
- Class 2 = 16″ Carriage Height (1500-5500 lbs. capacity)
- Class 3 = 20″ Carriage Height (6000-11,000 lbs. …
- Class 4 = 25″ Carriage Height (11,500-17,500 lbs. …
- Class 5 = 29″ Carriage Height (18,000-up lbs.
How wide do forklift forks go?
High capacity forklifts can have fork spacings as much as 9 or 10 feet. Generally, the forks can be adjusted from almost no clearance between them to the maximum spacing of the particular lift truck.