What must you check before using an attachment on a forklift?

What must be done before using a forklift?

1) Conducting a visual check

OSHA requires that all forklifts be examined at least daily before they are used to ensure that they’re in safe operating condition. If forklifts are used on a round-the-clock basis, then they must be examined after each shift.

What is a forklift attachment?

A forklift attachment is a modification or addition to a forklift that affects its capacity, stability, or safe operation. Lifting devices are used for lifting heavy loads, and when maintained for use with a forklift, do not affect the capacity or safe operation of the truck.

What should you check before lifting a load?

Check out these safe lifting and handling tips, recommended by the Health and Safety Executive.

  1. Think before you lift. …
  2. Keep the load close to the waist. …
  3. Adopt a stable position. …
  4. Ensure a good hold on the load. …
  5. Do not bend your back when lifting. …
  6. Do not bend the back any further while lifting. …
  7. Do not twist when you lift.
THIS IS INTERESTING:  How do I change the speed on my Toyota forklift?

When using a different attachment How will it affect the forklift?

Because different attachments have a different effect on the forklift’s capacity and stability, it is advised to always travel at a safe speed and take greater care when manoeuvring the forklift. When selecting an attachment, WorkCover NSW advises that attachments must be: Designed by a competent engineer.

What are 3 fluid levels that need to be checked before using the forklift?

Check of liquid Levels:

  • Hydraulic fluid.
  • Brake fluid.
  • Engine oil coolant.
  • Battery.
  • Fuel.

20.04.2011

What steps should you do every time you park a forklift?

Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.

Which side of the forklift is supporting more weight?

Weight distribution refers not only to the weight of the load, but also the weight of the forklift itself. An empty forklift has most of its weight in the rear, but when a load is placed on the lift, the weight distribution moves forward.

What are the three major parts of a forklift?

The three major parts of a lift truck are the body (truck), overhead guard, and hydraulic lift.

Where is the vehicle specification plate on a forklift?

The forklift data plate can be found on the instrument panel near the operating controls. It is the responsibility of the operator to understand the capabilities of each forklift and to properly maintain the data plate to ensure it is legible and complete.

THIS IS INTERESTING:  Do crane operators have bathrooms?

What is the correct way to lift heavy objects?

Bend your hips and knees to squat down to your load, keep it close to your body, and straighten your legs to lift. Never lift a heavy object above shoulder level. Avoid turning or twisting your body while lifting or holding a heavy object.

Which is the correct way to access the load?

Keep the load close to the body for as long as possible while lifting. Keep the heaviest side of the load next to the body. If a close approach to the load is not possible, try to slide it towards the body before attempting to lift it. Avoid twisting the back or leaning sideways, especially while the back is bent.

What will make the load more stable during travel?

When traveling with a load, always make sure to tilt the mast of the forklift backward so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.

How often should you inspect a forklift?

Federal OSHA requires that forklift vehicles have to be inspected at least daily, or after each shift when used around the clock. You will find this requirement in the Powered Industrial Truck standard at 1910.178(q)(7).

When you add a different attachment to a forklift what will be the most likely effect to the forklift’s lifting capacity?

It may also damage your forklift’s motor, hydraulics, and other costly parts. Using forklift attachments will affect the maximum load capacity of your forklift. While attachments will never increase the highest possible weight your vehicle can lift, they often will decrease it.

THIS IS INTERESTING:  Is propane for forklift same as grill propane?

What is forklift side shift?

When installed on a forklift a side-shift allows a carried load to be moved left or right within a given span. The major advantage of side-shift is the ability to move the fork carriage without having to move the whole forklift. Some other benefits of side-shift include: Ability to shift loads in tight spaces.

Special equipment and operation