When driving a forklift its forks should be at which of the following heights?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back.

When traveling with empty forklifts The forks should be in what position?

When travelling in an empty forklift, the forks of the lift should be in the position of waist high.

When parking a forklift how must the fork arms be positioned?

Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.

How do you adjust forklift forks?

Raise the fork slightly. The fork will be resting in a small groove in the crossbar; nudge the fork out of the notch so that it will slide along the top of the crossbar. If the forks are rarely adjusted they may be very hard to move. If so, move to the end of the fork and move it from side to side to break it free.

THIS IS INTERESTING:  What is the rule of flag hoisting?

Which of the following actions should be taken when driving a forklift?

You need to be constantly vigilant to drive a forklift safely.

Driving with load:

  • Smooth starting and stopping.
  • Proper speed.
  • Sounds horn at corners and intersections.
  • Keeps to right in two-way traffic.
  • Leaves at least three lengths behind other vehicles.
  • Prevents product damage by proper handling of load.

How far should you stand from a forklift?

The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.

What are the controls on a forklift?

Hydraulic Lift Knobs: Forklift has three basic controls knobs. One that lifts the forks up or down, the second one tilts the forks/blades down or up to secure the load, and the third to move the load side to side. Some types of forklifts have a knob that controls the width of the fork.

Is it illegal to leave keys in a forklift?

You might not be aware but it is actually illegal to leave the keys in an unattended Forklift. This measure is to prevent unauthorised use of the Forklift. … All forklifts and plant equipment can be fitted with low cost Driver Identification systems which prevent unauthorised usage.

Why are forklifts dangerous?

There are many factors that explain why forklifts are dangerous: Forklifts are heavy. … The weight of a forklift is unevenly distributed, which makes it harder to operate and drive. The rear wheels of a forklift are responsible for turning the vehicle, increasing the chances of tipping during tight turns.

THIS IS INTERESTING:  Where are Linde forklifts made?

What is the correct way to approach a stack with a forklift?

The stack should be approached squarely and carefully and the load, (or forks), should be around about 15 cm, (6 ins), away from the stack. This is to discourage pedestrians from walking through the gap. It helps considerably if the truck’s steering wheels are straight at this stage.

What is side shift on a forklift?

When installed on a forklift a side-shift allows a carried load to be moved left or right within a given span. The major advantage of side-shift is the ability to move the fork carriage without having to move the whole forklift. Some other benefits of side-shift include: Ability to shift loads in tight spaces.

At what speed should a forklift be operated?

What OSHA says: Where appropriate to the worksite, equip trucks with … visual devices (such as lights or blinkers) ANSI/ITSDF B56. 1-2011. The Material Handling Equipment Distributors Association (MHEDA) recommends a max speed of 8 mph in general and a 3 mph max speed in areas where pedestrians are present.

What is a fork positioner on a forklift?

A fork positioner allows you to hydraulically move the forks closer together or further apart, individually or together. This is particularly useful when you have to handle a variety of pallet sizes. … Fork positioners are commonly used in industries such as agriculture, paper handling, construction, food and beverage.

What are the 7 classes of forklifts?

The 7 Classes of Forklift Trucks

  • Class 1: Electric Motor Rider Trucks.
  • Class 2: Electric Motor Narrow Aisle Trucks.
  • Class 3: Electric Motor Hand or Hand-Rider Trucks.
  • Class 4: Internal Combustion Engine Trucks—Cushion Tires.
  • Class 5: Internal Combustion Engine Trucks—Pneumatic Tires.
THIS IS INTERESTING:  Your question: Who owns Yale forklift?

What is the most common type of forklift?

Counterbalance Lift

The Counterbalance is the most common type of forklift. This type of lift has its forks at the front of the machine and is designed with a weight in the back to offset or counter the balance of the load on the front.

How is forklift capacity calculated?

The maximum Load Moment for a truck is derived by multiplying the weight rating of the forklift by the center load distance. If we multiply the 5,000-pound capacity of our theoretical forklift by its 24-inch center load, we arrive at a maximum Load Moment of 120,000 inch-pounds.

Special equipment and operation