When traveling with empty forklift the forks should be in what position?

When travelling in an empty forklift, the forks of the lift should be in the position of waist high.

When traveling unloaded the forks should be raised?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.

When traveling up or down slopes How should the forklift forks be pointed?

How do you maintain control when traveling up or downhill?

  1. Loaded trucks, when travelling up and down hill that is greater than a 5% grade, should travel with the load pointed uphill.
  2. Unloaded truck should travel with the forks (load-engaging means) pointed down hill regardless of the grade.
THIS IS INTERESTING:  Are forklift extensions legal?

What is the safest position for your forklift when driving down a ramp with an empty forklift?

Q: What is the safest position for your forklift when you are driving down a ramp with an empty forklift? A: When driving down a ramp with an empty forklift, travel in reverse and keep the lift’s forks pointed downward.

What is the height range an operator should have their forks at when traveling?

A properly trained operator will carry his forks or load 4-6 inches off the ground. This position is high enough to reduce contact with dock plates, expansion joints in concrete, uneven areas, slight slopes, inclines and debris on operating surfaces.

How far should you stand from a forklift?

The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.

How many inches should forks be off the ground?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.

What is the correct behavior when driving a loaded forklift up an incline?

If you drive a forklift on an incline, you must keep the load on the uphill side.

What direction must the load be in when going uphill?

Always drive straight forward when going uphill. So never drive uphill diagonally and never start turning on a slope. When loaded, the load must be in the highest position in relation to the slope (forwards uphill and backwards downhill).

THIS IS INTERESTING:  Your question: How much is it to lease a forklift?

Which side of the forklift is supporting more weight?

Weight distribution refers not only to the weight of the load, but also the weight of the forklift itself. An empty forklift has most of its weight in the rear, but when a load is placed on the lift, the weight distribution moves forward.

When operating a loaded forklift going up a ramp you must?

Specific precautions are required when driving forklifts on ramps with grades over 10%. Loaded forklifts must be driven with the load pointed up the ramp (good standard practice is to ALWAYS drive with the load pointed up the ramp or slope).

Why is it dangerous to turn a forklift on a ramp or slope?

Not only can operators be at risk when travelling recklessly on slopes but the safety of pedestrians is also compromised. The load in which the forklift operator may be transporting can also be significantly damaged or even destroyed if safety precautions are not followed within this situation.

What is the first thing you need to do before raising or lowering a load?

Check that the overhead clearance is adequate before raising loads. Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator.

What steps should you do every time you park a forklift?

Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.

THIS IS INTERESTING:  What is a 3 stage forklift?

Where is the vehicle specification plate on a forklift?

The forklift data plate can be found on the instrument panel near the operating controls. It is the responsibility of the operator to understand the capabilities of each forklift and to properly maintain the data plate to ensure it is legible and complete.

When driving a forklift who has the right of way?

Operators should yield the right of way to pedestrians: This is an OSHA recommendation that all forklift drivers should be aware of. Because of the size and power of the forklift, operators should stop and wait for pedestrians to clear the area before proceeding along their route with caution.

Special equipment and operation