Which steps must be done at least daily before using a forklift?

OSHA requires that all forklifts be examined at least daily before they are used to ensure that they’re in safe operating condition. If forklifts are used on a round-the-clock basis, then they must be examined after each shift.

What should I check before operating a forklift?

Forklift Pre-Operation Checklist

  • Fluid levels — oil, water, and hydraulic fluid.
  • Leaks, cracks or any other visible defect including hydraulic hoses and mast chains. …
  • Tire condition and pressure including cuts and gouges.
  • Condition of the forks, including the top clip retaining pin and heel.
  • Load backrest extension.

Which steps should you do every time you park a forklift?

Parking Safety Rules

  • Always try to find a level surface to park on. …
  • Lower forks, or the forklift attachment, all the way to the ground. …
  • Put the gear into neutral.
  • Make sure the wheels are straight. …
  • Set the parking brake every time you park the forklift. …
  • Turn off the engine before dismounting the forklift.
THIS IS INTERESTING:  Can you use slings on a forklift?

Which safety precaution applies to forklifts?

Forklift operators should be dressed with the appropriate safety equipment, including safety shoes, hard-hats, and a high-visibility jacket. Make sure to tuck away loose clothing to prevent it from getting caught on the forklift.

What is the first thing you do before operating a forklift?

The first step toward safe forklift operation is conducting the preoperational inspection. Forklift operators should conduct the inspection at the start of each work shift to ensure that the forklift will work properly. According to OSHA, 1 in 15 forklift-related accidents are caused by improper maintenance.

What are 3 fluid levels that need to be checked before using the forklift?

Check of liquid Levels:

  • Hydraulic fluid.
  • Brake fluid.
  • Engine oil coolant.
  • Battery.
  • Fuel.

20.04.2011

When parking or leaving the forklift you must remove the ignition key?

Turn off the engine and the key should be removed

Aside from turning off the engine, and you know you will be away for a longer period, removing the key from the ignition and handing it over to your shift supervisor in case someone wants it to be used during that period is good practice as well.

At what distance is a forklift considered to be unattended?

Note: A powered industrial truck is unattended when the operator is 25 feet or more away from the vehicle which remains in his view, or whenever the operator leaves the vehicle and it is not in his/her view.

Is it illegal to leave keys in a forklift?

You might not be aware but it is actually illegal to leave the keys in an unattended Forklift. This measure is to prevent unauthorised use of the Forklift. … All forklifts and plant equipment can be fitted with low cost Driver Identification systems which prevent unauthorised usage.

THIS IS INTERESTING:  Do you need a driver's license to drive a forklift in Ontario?

What is the most common type of forklift?

Counterbalance Lift

The Counterbalance is the most common type of forklift. This type of lift has its forks at the front of the machine and is designed with a weight in the back to offset or counter the balance of the load on the front.

What are the types of forklifts?

10 Common Forklift Types, Classifications and Uses

  • Warehouse Forklift.
  • Side Loader.
  • Counterbalance Forklift.
  • Telehandler.
  • Industrial Forklift.
  • Rough Terrain Forklift.
  • Pallet Jack.
  • Walkie Stacker.

10.09.2018

What is another name for a forklift?

A forklift (also called lift truck, jitney, fork truck, fork hoist, and forklift truck) is a powered industrial truck used to lift and move materials over short distances.

Why do forklifts have 3 pedals?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. That third pedal is called an Inching Brake. … It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

What are the 3 main guards on a forklift?

One final passive safety feature is the overhead guard. In the unlikely event that part of the load falls off of a raised pallet, the overhead guard is designed to protect the operator from small objects. The overhead guard is constructed to a very high standard and is an integral part of the forklift’s design.

Which side of the forklift is supporting more weight?

Weight distribution refers not only to the weight of the load, but also the weight of the forklift itself. An empty forklift has most of its weight in the rear, but when a load is placed on the lift, the weight distribution moves forward.

THIS IS INTERESTING:  Quick Answer: How much weight can a truck crane lift?
Special equipment and operation