You asked: How long are standard forklift forks?

Fork Length – The most common fork length is 42-inchs for both Class II and Class III carriages. This size allows for a standard 48-inch length pallet to be adequately supported without the fork tips protruding and possibly damaging whatever is behind the skid.

How long is a standard fork?

Length of fork (L) – measure from the end of the tip to the shank. Length can be given in mm or inches, common lengths are 48” inch, 72” inch and 96” inch. Width (W) = width of the fork at its widest point. Thickness (T) = thickness of the forks is measure on the shank.

What is the size of forklift forks?

Forklift forks, 48″ length, 2 piece set, 5,720lbs lifting capacity, 48″ Length x 4″ Width x 1-3/4″ Thickness.

Are all forklift forks the same?

People who don’t work with forklifts all the time often assume that there is only one type of forks that fit onto lift trucks. There are actually many different types of forks, most of which are interchangeable depending on how you plan to use your forklift. Forklifts can different types of forks.

THIS IS INTERESTING:  Frequent question: Are slings compatible with hoists?

How wide is a standard fork lift?

Standard forklifts generally measure between 4 to 7 ft wide and 8 to 10 ft long.

What grade of steel are forklift forks?

Forklift tines are usually made from 4340, a very tough steel.

How much are forks for a forklift?

Class 2

STD TAPER
SIZE PRICE /PR CAPACITY PER PAIR @24″LC LBS.
1.50x4x72 $592.50 5420
1.75x4x36 $367.50 6860
1.75x4x42 $400.00 6860

How do you read forklift forks?

Check blade and shank angle – If the shank and blade angle exceed 93 degrees, the fork must be replaced. Do not allow machine shops to bend forks back into place! Ensure straightness of blade and shank – If the shank or the blade are bent, the fork can no longer be used.

What is a Class 2 forklift?

Class II forklifts are electric, narrow aisle models. As the name suggests, Class II forklifts are designed with maneuverability that allows them to operate in tight spaces and narrow aisles.

How heavy is a forklift?

The average automobile weighs approximately 3,000 lbs and the average forklift weighs close to 9,000 lbs.

How do you adjust forklift forks?

Raise the fork slightly. The fork will be resting in a small groove in the crossbar; nudge the fork out of the notch so that it will slide along the top of the crossbar. If the forks are rarely adjusted they may be very hard to move. If so, move to the end of the fork and move it from side to side to break it free.

Are forklift forks interchangeable?

Forks must meet industry standards that make them interchangeable, regardless of the lift truck manufacturer; however, they are specific to the capacity of the forklift.

THIS IS INTERESTING:  How does a tower crane climb?

How high is a 2 stage forklift?

A typical two stage mast for a forklift with a capacity from 2,000 lbs. to 6,000 lbs. will have approximately 130″ of maximum lift and will be around 83-88″ Overall Height Lowered (OAHL). Two stage masts are very common in high capacity forklifts of 15,000 lbs.

What class lift trucks should not turn on an incline?

PEDESTRIANS AND FORKLIFTS SHOULD NEVER OCCUPY A RAMP OR INCLINE AT THE SAME TIME, IF THE OPERATOR OF A CLASS 1, 4, & 5 IS CARRYING A LOAD THAT BLOCKS THEIR FORWARD VISION ON LEVEL SURFACES, THEY ARE TAUGHT TO DRIVE IN REVERSE. BUT WHEN APPROACHING A RAMP OR INCLINE, THAT LOAD MUST FACE UPHILL.

What is maximum fork height?

Maximum fork height is the distance from the ground to the lifting surface of the forks with the mast fully lifted. A common height is 188 inches or 15’8”. While many fork heights are available, this mast is about as high as you can have and still work in a typical semi-trailer.

Special equipment and operation